Removing Tarnish on Mouthpieces

Post Reply
PaulT
Posts: 374
Joined: Wed Jul 18, 2018 9:55 pm
Location: North Dakota

Removing Tarnish on Mouthpieces

Post by PaulT »

Some mouthpieces I have put away after very little play have developed some tarnish [Bach/silver plated]. They were stored in drawer, not in sealed plastic bags (should they have been stored in sealed plastic bags?)

I have read of three methods of removing the tarnish:

1) an aluminum foil/baking soda/hot water bath
2) polishing cloth intended for use with silver and sliver plating
3) polishing/cleaning cream intended for use with silver and silver plating.

- Are the treatments equal? Is one preferable in general or in a particular situation? Is there a sequence or hierarchy in which they should be used or combined? Comments on "pros and cons"

- Is there a downside to tarnish removal or a reason to avoid tarnish removal treatments in cases where the tarnish is minimal or light? (i.e. does it thin/compromise the plating)

Thanks
User avatar
BGuttman
Posts: 6295
Joined: Thu Mar 22, 2018 7:19 am
Location: Cow Hampshire

Re: Removing Tarnish on Mouthpieces

Post by BGuttman »

Lots to cover here.

1. Any tarnish removal process (except possibly the aluminum foil) will remove some plating. You have to remove the plating that has tarnished at the very least. Unless you have a highly sulfurous atmosphere (smells like rotten eggs) the amount of silver removed will be pretty small. I have some mouthpieces that are decades old and after tarnish removal they still look good.

2. The silver polishing cloth will only remove light tarnish, and not sulfide tarnish (rotten egg smell atmosphere). If all you have is a little darkening it will work fine. Otherwise, you need something more aggressive.

3. I've never tried the aluminum foil - baking soda - hot water technique, but some have said it really works well. Looks kinda messy to me.

4. I have used cream polishes and liquid polishes. I recommend the liquids. They are less aggressive to the plating.

5. If you store the mouthpieces in a drawer, there are tarnish resistant cloths that you just put in the drawer with the mouthpieces to slow down tarnish. These are sold for silver plate tableware.

Good luck.
Bruce Guttman
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
User avatar
greenbean
Posts: 1850
Joined: Fri Mar 23, 2018 6:14 pm
Location: San Francisco

Re: Removing Tarnish on Mouthpieces

Post by greenbean »

I use Goddard's Silver Dip. Only mpcs that I leave out will get pretty heavily tarnished. The ones in parts boxes, bags, or shoeboxes don't tarnish at all.
Tom in San Francisco
Currently playing...
Bach Corp 16M
Many French horns
User avatar
harrisonreed
Posts: 5165
Joined: Fri Aug 17, 2018 12:18 pm
Location: Fort Riley, Kansas
Contact:

Re: Removing Tarnish on Mouthpieces

Post by harrisonreed »

The aluminum foil method works best on light tarnish. You'd have to do it LOT on a heavily tarnished mouthpiece
User avatar
Doug Elliott
Posts: 3380
Joined: Wed Mar 21, 2018 10:12 pm
Location: Maryand

Re: Removing Tarnish on Mouthpieces

Post by Doug Elliott »

If this link works...
I cleaned some tarnished silverware with aluminum foil, baking soda, and poured boiling water on it. The whole process (and video) is 40 seconds.

"I know a thing or two because I've seen a thing or two."
User avatar
greenbean
Posts: 1850
Joined: Fri Mar 23, 2018 6:14 pm
Location: San Francisco

Re: Removing Tarnish on Mouthpieces

Post by greenbean »

Doug Elliott wrote: Mon Mar 22, 2021 11:28 pm If this link works...
I cleaned some tarnished silverware with aluminum foil, baking soda, and poured boiling water on it. The whole process (and video) is 40 seconds.

Whoa! That is awesome.
Tom in San Francisco
Currently playing...
Bach Corp 16M
Many French horns
Doubler
Posts: 393
Joined: Mon Jan 07, 2019 8:56 pm

Re: Removing Tarnish on Mouthpieces

Post by Doubler »

I tried the aluminum foil/baking soda/hot water method once on a piece that I had not dealt with before to see how it would work out. I followed the procedure exactly and was very disappointed. What works great for me is Flitz liquid for removal and Goddard's Silver Polishing Cloth for maintenance.
Current instruments:
Olds Studio trombone, 3 trumpets, 1 flugelhorn, 1 cornet, 1 shofar, 1 keyboard

Previous trombones:
Selmer Bundy, Marceau
User avatar
harrisonreed
Posts: 5165
Joined: Fri Aug 17, 2018 12:18 pm
Location: Fort Riley, Kansas
Contact:

Re: Removing Tarnish on Mouthpieces

Post by harrisonreed »

Doubler wrote: Tue Mar 23, 2021 4:17 am I tried the aluminum foil/baking soda/hot water method once on a piece that I had not dealt with before to see how it would work out. I followed the procedure exactly and was very disappointed. What works great for me is Flitz liquid for removal and Goddard's Silver Polishing Cloth for maintenance.
The water has to be salty and very hot, otherwise it doesn't work well.
User avatar
BGuttman
Posts: 6295
Joined: Thu Mar 22, 2018 7:19 am
Location: Cow Hampshire

Re: Removing Tarnish on Mouthpieces

Post by BGuttman »

I still recommend Flitz, Haggarty's, or Gorham. Liquid. Shake well.
Bruce Guttman
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
User avatar
TriJim
Posts: 63
Joined: Sun Mar 25, 2018 3:42 pm
Location: SouthCentral Pennsylvania

Re: Removing Tarnish on Mouthpieces

Post by TriJim »

Wright's Silver Polish - 'Cleans, Polishes, and Protects.' Comes in cream or liquid (which I use) forms and available at most retailers including WalMart, Home Depot, and Amazon. Easy to use and even removes light insertion marks.
PhilTrombone
Posts: 138
Joined: Tue Nov 06, 2018 10:50 am

Re: Removing Tarnish on Mouthpieces

Post by PhilTrombone »

I just used the Bon Ami cleanser (which is "non-abrasive") from my kitchen on 2 mouthpieces with light tarnish. They came out great.
User avatar
Doug Elliott
Posts: 3380
Joined: Wed Mar 21, 2018 10:12 pm
Location: Maryand

Re: Removing Tarnish on Mouthpieces

Post by Doug Elliott »

Bon Ami (from their website)
Natural soft abrasives (feldspar and limestone)

It's not "non-abrasive," it's just softer abrasives that are still an abrasive to an even softer surface like silver.

I might use something like that as a first step in cleaning and preparing a mouthpiece for replating, if it's horribly pitted. But I like Barkeeper's Friend for that.
"I know a thing or two because I've seen a thing or two."
baileyman
Posts: 1053
Joined: Fri Mar 23, 2018 11:33 pm

Re: Removing Tarnish on Mouthpieces

Post by baileyman »

A piece in a pocket rubbing around all the time and occasional sweaty hands will keep it looking pretty good. Just need a brush for the stem and throat.
User avatar
boneberg
Posts: 177
Joined: Sat Dec 19, 2020 12:39 pm
Location: Brandenburg/Berlin

Re: Removing Tarnish on Mouthpieces

Post by boneberg »

I've had great results (even with heavily tarnished ones) with the aluminum foil/baking soda/boiling water (not just hot) method in the last few weeks. I also very gently "massaged" the mpcs. with baking soda with my fingers beforehand. Most important is that you thoroughly clean off the residue from the chemical process afterwards (e.g. with dish washing liquid). I didn't find salt helpful or necessary.
BHolleyBrass
Posts: 30
Joined: Wed Apr 04, 2018 11:36 am

Re: Removing Tarnish on Mouthpieces

Post by BHolleyBrass »

Most shops don't exactly advertise it, but they'd probably polish a few mouthpieces for free. A bench motor or lathe, a mouthpiece-holding mandrel, some polish (I use Goddard's), and a few shop towels can knock out multiple mouthpieces in just a few minutes. Cleanup (before and after) with Dawn and a brush and it's one of those welcome little breaks from "real" repairs for our nice customers.
S.E. Shires Ralph Sauer Tenor
AR Resonance ML GR1 72
PhilTrombone
Posts: 138
Joined: Tue Nov 06, 2018 10:50 am

Re: Removing Tarnish on Mouthpieces

Post by PhilTrombone »

Bon Ami (from their website)
Natural soft abrasives (feldspar and limestone)

It's not "non-abrasive," it's just softer abrasives that are still an abrasive to an even softer surface like silver.

I might use something like that as a first step in cleaning and preparing a mouthpiece for replating, if it's horribly pitted. But I like Barkeeper's Friend for that.
Thanks Doug. Agreed. My equipment in question was only lightly tarnished, and a light touch is all that was needed. Both Mpieces came out sparkling in my case. Just a little bit of powder on a damp paper towel.

I do shudder at the thought of using aluminum foil on any metal surface. Ick!
MTbassbone
Posts: 491
Joined: Sat Apr 21, 2018 3:08 pm
Location: Silver Spring, MD

Re: Removing Tarnish on Mouthpieces

Post by MTbassbone »

Any opinions about Flitz?
User avatar
harrisonreed
Posts: 5165
Joined: Fri Aug 17, 2018 12:18 pm
Location: Fort Riley, Kansas
Contact:

Re: Removing Tarnish on Mouthpieces

Post by harrisonreed »

PhilTrombone wrote: Tue Mar 23, 2021 4:41 pm
Bon Ami (from their website)
Natural soft abrasives (feldspar and limestone)

It's not "non-abrasive," it's just softer abrasives that are still an abrasive to an even softer surface like silver.

I might use something like that as a first step in cleaning and preparing a mouthpiece for replating, if it's horribly pitted. But I like Barkeeper's Friend for that.
Thanks Doug. Agreed. My equipment in question was only lightly tarnished, and a light touch is all that was needed. Both Mpieces came out sparkling in my case. Just a little bit of powder on a damp paper towel.

I do shudder at the thought of using aluminum foil on any metal surface. Ick!
The aluminum foil just sits in the water with the mouthpiece -- it doesn't even have to touch the mouthpiece. Often people will use a disposable aluminum lasagna tin. The sodium ions in the water carry the sulphur atoms from the mouthpiece to the aluminum foil. As long as the water is near boiling and there is plenty of baking soda in the slurry, the tarnish vanishes like magic. Science.
Doubler
Posts: 393
Joined: Mon Jan 07, 2019 8:56 pm

Re: Removing Tarnish on Mouthpieces

Post by Doubler »

MTbassbone wrote: Tue Mar 23, 2021 4:59 pm Any opinions about Flitz?
See my post and BGuttman's above.
Current instruments:
Olds Studio trombone, 3 trumpets, 1 flugelhorn, 1 cornet, 1 shofar, 1 keyboard

Previous trombones:
Selmer Bundy, Marceau
User avatar
Doug Elliott
Posts: 3380
Joined: Wed Mar 21, 2018 10:12 pm
Location: Maryand

Re: Removing Tarnish on Mouthpieces

Post by Doug Elliott »

The aluminum foil does have to touch the mouthpieces. Did my video work? I can't tell from my end.

The black sulfur transfers from the mouthpiece to the aluminum foil through electrolysis. It leaves the silver on the mouthpiece, there's no silver loss.
"I know a thing or two because I've seen a thing or two."
User avatar
BGuttman
Posts: 6295
Joined: Thu Mar 22, 2018 7:19 am
Location: Cow Hampshire

Re: Removing Tarnish on Mouthpieces

Post by BGuttman »

A couple of notes:

Creams generally have coarser abrasives and tend to remove more silver. Better on deep tarnish, but if you get too aggressive you can polish off the plating faster than with a liquid.

I didn't mention Wright's. Works OK as well.

Polishes intended for multi metals or brass tend to be too aggressive on silver plate. Often they contain a lot of ammonia which complexes silver. While I have worked with Noxon with some success, I don't recommend it.
Bruce Guttman
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
User avatar
harrisonreed
Posts: 5165
Joined: Fri Aug 17, 2018 12:18 pm
Location: Fort Riley, Kansas
Contact:

Re: Removing Tarnish on Mouthpieces

Post by harrisonreed »

Doug Elliott wrote: Tue Mar 23, 2021 5:34 pm The aluminum foil does have to touch the mouthpieces. Did my video work? I can't tell from my end.

The black sulfur transfers from the mouthpiece to the aluminum foil through electrolysis. It leaves the silver on the mouthpiece, there's no silver loss.
The video works Doug. You're right about it needing to touch at least a point on the item (which creates a tiny electric current), but as is very apparent in your video the aluminum doesn't need to come into contact with all or even a large percentage of the tarnish for it to "vanish".

I was trying to respond to the "eek" comment above about "using" the aluminum foil on a metal surface. It's not like Doug is scrubbing tarnish off using the foil in his video.
PhilTrombone
Posts: 138
Joined: Tue Nov 06, 2018 10:50 am

Re: Removing Tarnish on Mouthpieces

Post by PhilTrombone »

I was trying to respond to the "eek" comment above about "using" the aluminum foil on a metal surface. It's not like Doug is scrubbing tarnish off using the foil in his video.
Ah. now I get it. Science is in fact, cool!
Amconk
Posts: 245
Joined: Thu Jun 14, 2018 11:30 am
Location: 97524

Re: Removing Tarnish on Mouthpieces

Post by Amconk »

Plain old toothpaste. Work it in with a cloth, or even just your hands. Give it a rinse and a polish with your favorite polish cloth. Voila!
Michael Conkey
Southern Oregon Trombonist

-ETB-643R
-Jin Bao Alto
User avatar
Doug Elliott
Posts: 3380
Joined: Wed Mar 21, 2018 10:12 pm
Location: Maryand

Re: Removing Tarnish on Mouthpieces

Post by Doug Elliott »

Toothpaste is actually more abrasive than silver polish. If you care.
"I know a thing or two because I've seen a thing or two."
User avatar
greenbean
Posts: 1850
Joined: Fri Mar 23, 2018 6:14 pm
Location: San Francisco

Re: Removing Tarnish on Mouthpieces

Post by greenbean »

Bon Ami and Barkeeper's Friend. I use these a lot for around-the-house cleaning. They are abrasive but less so than Comet or Ajax. But they will leave a silver-plated mouthpiece covered in tiny scratches. (Ask me how I know...)

Toothpaste? Mine stays in the bathroom!

Silver dip. Works well. I removes the sulphur only. Seems like the safest way to go. Doug, any thoughts?...
Tom in San Francisco
Currently playing...
Bach Corp 16M
Many French horns
bigbandbone
Posts: 589
Joined: Thu Jan 17, 2019 7:45 am

Re: Removing Tarnish on Mouthpieces

Post by bigbandbone »

If you do not have access to a bench motor and chamois buffs here is what I would suggest.

First dip it in liquid Tarnishield. This will get the tarnish out of the deep grooves. Then mix baking soda with water till you get a mushy texture. Use this with you fingers and a mouthpiece brush to clean the inside of the cup and bore. Then mix Haggerty's with denatured alcohol. You don't need much Haggerty's. Wipe the watery mixture onto the mouthpiece with a clean rag, let it dry to a haze, then polish with a piece of flannel.

This is how I did it for years in my shop. Except I buffed it out on an unstitched chamois wheel with green rouge.
blahMark
Posts: 5
Joined: Tue Mar 30, 2021 10:00 pm

Re: Removing Tarnish on Mouthpieces

Post by blahMark »

A lot of convoluted responses. Why not just use silver polish? I imagine if you polish it weekly it could wear through the plating eventually, but that seems like a nonexistent problem.
CharlieB
Posts: 365
Joined: Thu Mar 29, 2018 7:51 pm
Location: Maryland

Re: Removing Tarnish on Mouthpieces

Post by CharlieB »

Another solution is to celebrate the patina.
The black oxidation shines up very nicely with a little rubbing from a cotton cloth.
Surprisingly, after the initial rubbing, the patina is very durable and requires almost no maintenance.
There are several simple ways to accelerate the initial blackening (Google).
I use this method on the vintage mouthpieces for my old horns; partly because of aesthetics, partly because it avoids the loss of silver plating caused by repeated polishings, and partly so I don't need to keep polishing mouthpieces.
User avatar
harrisonreed
Posts: 5165
Joined: Fri Aug 17, 2018 12:18 pm
Location: Fort Riley, Kansas
Contact:

Re: Removing Tarnish on Mouthpieces

Post by harrisonreed »

Does silver tarnish tear your face up? I used to have all kinds of lip trouble (like skin issues) from silver mouthpieces, but now I prefer them. I wonder if the difference is in how I've been careful to really maintain my mouthpieces?
User avatar
JohnL
Posts: 1854
Joined: Fri Mar 23, 2018 9:01 am
Contact:

Re: Removing Tarnish on Mouthpieces

Post by JohnL »

harrisonreed wrote: Thu Apr 01, 2021 7:33 am Does silver tarnish tear your face up? I used to have all kinds of lip trouble (like skin issues) from silver mouthpieces, but now I prefer them. I wonder if the difference is in how I've been careful to really maintain my mouthpieces?
It might have been other, non-tarnish grunge that was causing the irritation. Getting the oxidation off gets rid of a lot of other stuff, too.
User avatar
harrisonreed
Posts: 5165
Joined: Fri Aug 17, 2018 12:18 pm
Location: Fort Riley, Kansas
Contact:

Re: Removing Tarnish on Mouthpieces

Post by harrisonreed »

JohnL wrote: Thu Apr 01, 2021 10:57 am
harrisonreed wrote: Thu Apr 01, 2021 7:33 am Does silver tarnish tear your face up? I used to have all kinds of lip trouble (like skin issues) from silver mouthpieces, but now I prefer them. I wonder if the difference is in how I've been careful to really maintain my mouthpieces?
It might have been other, non-tarnish grunge that was causing the irritation. Getting the oxidation off gets rid of a lot of other stuff, too.
Yeah it could be that I'm keeping them much cleaner in general. I also thought about maybe it was that I was occasionally using a polishing cloth on the rim and rinsing it off, which might have made the surface abrasive over time.

In any case, as it relates, once I stopped doing this and just detarnished with baking soda every year or so, no more torn up face.
Pistolero
Posts: 7
Joined: Thu Apr 29, 2021 1:52 pm

Re: Removing Tarnish on Mouthpieces

Post by Pistolero »

Amconk wrote: Wed Mar 24, 2021 6:58 pm Plain old toothpaste. Work it in with a cloth, or even just your hands. Give it a rinse and a polish with your favorite polish cloth. Voila!
You nailed it, Colgate regular toothpaste for the WIN!
Posaunus
Posts: 3888
Joined: Fri Mar 23, 2018 9:54 pm
Location: California

Re: Removing Tarnish on Mouthpieces

Post by Posaunus »

Pistolero wrote: Sun May 02, 2021 1:13 pm
Amconk wrote: Wed Mar 24, 2021 6:58 pm Plain old toothpaste. Work it in with a cloth, or even just your hands. Give it a rinse and a polish with your favorite polish cloth. Voila!
You nailed it, Colgate regular toothpaste for the WIN!
Doug Elliott wrote: Wed Mar 24, 2021 8:05 pm Toothpaste is actually more abrasive than silver polish. If you care.
greenbean wrote: Tue Mar 30, 2021 10:09 am Toothpaste? Mine stays in the bathroom!

Silver dip. Works well. I removes the sulphur only. Seems like the safest way to go.
I see no point in scratching the shiny mouthpiece finish or prematurely removing silver plate. Remove tarnish only infrequently, as necessary, using the gentlest methods / materials possible. And try to avoid tarnish in the first place. Gently wipe your mouthpiece dry with a clean microfiber cloth after each playing session, and store dry. (Hint: don't use a leather mouthpiece pouch!)
sungfw
Posts: 234
Joined: Tue Jul 17, 2018 5:15 am

Re: Removing Tarnish on Mouthpieces

Post by sungfw »

I concur with those who recommend stay away from toothpaste. Yes, toothpaste will remove the tarnish … along with a whole lot more that you possibly/probably DON'T want to remove.

10-12 years ago, I took the used Eastman by Shires British Baritone I bought on ebay to Mike Morse at Tuba Exchange to have him look at the second valve which was occasionally hanging slightly on the return stroke. Mike checked the piston, found there was a slight high spot on one side and suggested that before I sent it somewhere to get it lapped (this was right after Vince Simonetti instituted a policy that they would only work on a horn if you bought it from them), I try lapping it myself using a little dab of toothpaste—"about the size of the end of your little finger."

Figured, why the heck not since the horn and shipping cost me less than $150 and 30-40 minutes later the action was as smooth as glass.
Post Reply

Return to “Maintenance”