Page 1 of 1
Oily bubble leak
Posted: Wed Oct 07, 2020 9:19 pm
by Roberto28
Hi guys,
At the beginning the year I had my horn‘S f-attachment converted into an Instrument Innovations rotor system. So the Brass technician had to take the old f-attachment out and resolder new parts.
Tonight while lubricating the rotor I noticed a bubble at one of the joints where the new soldering was done. I was pressing down the F-tuning slide without activating the trigger.
Is the bubble normal? Should I be concerned?
Re: Oily bubble leak
Posted: Wed Oct 07, 2020 9:38 pm
by Burgerbob
Might be leaking at that joint. For future reference, it's a good idea to always activate the valve when moving the F slide.
Re: Oily bubble leak
Posted: Wed Oct 07, 2020 9:47 pm
by Roberto28
Yes, I agree about activating the trigger. I see that now. Do you think I need have that looked at, or should I just let *slide*?
Re: Oily bubble leak
Posted: Wed Oct 07, 2020 10:15 pm
by Burgerbob
I might have it checked out. If you can see it, it might be a serious enough leak to effect how the horn plays.
Re: Oily bubble leak
Posted: Thu Oct 08, 2020 7:32 am
by ZacharyThornton
You should have that checked out.
Re: Oily bubble leak
Posted: Thu Oct 08, 2020 8:44 am
by hornbuilder
A bubble at a solder joint indicates a leak.
Re: Oily bubble leak
Posted: Thu Oct 08, 2020 9:20 am
by Bonearzt
There really isn't enough pressure build up when you pull the slide to cause problems.
Re: Oily bubble leak
Posted: Thu Oct 08, 2020 10:53 am
by Kingfan
Duct tape. Fixed!
Re: Oily bubble leak
Posted: Thu Oct 08, 2020 2:22 pm
by Bonearzt
Kingfan wrote: ↑Thu Oct 08, 2020 10:53 am
Duct tape. Fixed!
Did you put Bondo underneath? Or Superglue?
Re: Oily bubble leak
Posted: Thu Oct 08, 2020 3:26 pm
by BGuttman
Bonearzt wrote: ↑Thu Oct 08, 2020 2:22 pm
Kingfan wrote: ↑Thu Oct 08, 2020 10:53 am
Duct tape. Fixed!
Did you put Bondo underneath? Or Superglue?
JB Weld
Re: Oily bubble leak
Posted: Thu Oct 08, 2020 3:35 pm
by Posaunus
Bonearzt wrote: ↑Thu Oct 08, 2020 2:22 pm
Kingfan wrote: ↑Thu Oct 08, 2020 10:53 am
Duct tape. Fixed!
Did you put Bondo underneath? Or Superglue?
Plumber's Putty? Chewing gum!
Re: Oily bubble leak
Posted: Thu Oct 08, 2020 5:15 pm
by Kingfan
Posaunus wrote: ↑Thu Oct 08, 2020 3:35 pm
Bonearzt wrote: ↑Thu Oct 08, 2020 2:22 pm
Did you put Bondo underneath? Or Superglue?
Plumber's Putty? Chewing gum!
All of the above. You can't be too careful!
Re: Oily bubble leak
Posted: Fri Oct 09, 2020 5:21 am
by timothy42b
BGuttman wrote: ↑Thu Oct 08, 2020 3:26 pm
Bonearzt wrote: ↑Thu Oct 08, 2020 2:22 pm
Did you put Bondo underneath? Or Superglue?
JB Weld
JBWeld stopped the leak at the top of my daughter's Volvo radiator and it held several years, was still going strong when we eventually junked the car. (blown head gasket on a 1991 with some other problems, it was time to move on).
If it can stop the pressure and heat of a Volvo, pretty sure it will hold against breath pressure.
Of course no tech will ever want to work on your horn again! That stuff is a pain to get off. If you even can.