Rotor Bumpers
-
- Posts: 460
- Joined: Wed Jul 11, 2018 1:51 pm
- Location: New Albany, Ohio
Rotor Bumpers
At practice with nothing to do but count 30+ measures of rests I gave my horn a close visual inspection. I discovered one of my rotor bumpers was torn and about to fall out of its holder (the bumper you hit when the valve is activated). I can't think of when I ever gave those bumpers more than a cursory glance.
Took it to a local music store who are very good about replacing small wear items while you wait. The person at the counter took it back and reappeared in a couple of minutes. The torn (neoprene?) bumper was out and a nicely sized piece of good old cork was in its place.
Later when I played the horn I noticed a much more firm stop as the valve was activated. I imagine the valve was over rotating with the neoprene bumper and actually constricting the air passage to the F attachment. Also noticed that the low C and F are much more stable.
I was surprised
Took it to a local music store who are very good about replacing small wear items while you wait. The person at the counter took it back and reappeared in a couple of minutes. The torn (neoprene?) bumper was out and a nicely sized piece of good old cork was in its place.
Later when I played the horn I noticed a much more firm stop as the valve was activated. I imagine the valve was over rotating with the neoprene bumper and actually constricting the air passage to the F attachment. Also noticed that the low C and F are much more stable.
I was surprised
Dave
2020ish? Shires Q30GR with 2CL
1982 King 607F with 13CL
Yamaha 421G Bass with Christian Lindberg 2CL / Bach 1 1/2G
Bach Soloist with 13CL
1967 Olds Ambassador with 10CL
1957 Besson 10-10
Jean Baptiste EUPCOMS with Stork 4
2020ish? Shires Q30GR with 2CL
1982 King 607F with 13CL
Yamaha 421G Bass with Christian Lindberg 2CL / Bach 1 1/2G
Bach Soloist with 13CL
1967 Olds Ambassador with 10CL
1957 Besson 10-10
Jean Baptiste EUPCOMS with Stork 4
- BGuttman
- Posts: 6295
- Joined: Thu Mar 22, 2018 7:19 am
- Location: Cow Hampshire
Re: Rotor Bumpers
It's entirely possible the neoprene bumper was worn or compressed and the replacement is fitted better. Cork isn't inherently better or worse than neoprene, but you will find it a bit firmer than the rubber.
Bruce Guttman
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
- TriJim
- Posts: 63
- Joined: Sun Mar 25, 2018 3:42 pm
- Location: SouthCentral Pennsylvania
Re: Rotor Bumpers
Speaking of firmer - I use the stock Bach replacement bumpers (black neoprene rubber) on my Bach A47 (MLR) trombone valve; [Hickey's (item #054017)]. However; they quickly (4-6 mo) become firm/hard and make a lot of noise when the rotor is applied or released. The bumpers are not exposed to heat, cold or sunlight, but they do come in contact with rotor lube.
Anyone recommend a better bumper option (to replace stock Bach bumpers) that retain their flex and remain quiet?
Anyone recommend a better bumper option (to replace stock Bach bumpers) that retain their flex and remain quiet?
-
- Posts: 1158
- Joined: Thu May 10, 2018 1:39 pm
Re: Rotor Bumpers
A little drop of valve oil will soften the bumpers, but will hasten them wearing out (slightly).
Jim Scott
Jim Scott
-
- Posts: 666
- Joined: Tue Nov 02, 2021 11:44 am
Re: Rotor Bumpers
I lubricate valve(s) every day by removing the tuning slide(s). I put a few drops of Holton Rotary Valve Oil down the open tubing and replace the tuning slide(s). Once a month I take the valve cap off and put one drop of Holton Rotary Valve Oil on the bearing. I don’t get or put oil on the bumpers. I pack Bach’s goofy ball and socket fitting with Vaseline as required, once a week or once a month, just to keep the racket down.
Treat it like it was a combine during harvest, and replace the bumpers and strings, every winter, if they need it.
Treat it like it was a combine during harvest, and replace the bumpers and strings, every winter, if they need it.
Richard Smith
Wichita, Kansas
Wichita, Kansas
- ithinknot
- Posts: 1107
- Joined: Fri Jul 24, 2020 3:40 pm
Re: Rotor Bumpers
If you want to be really pretentious like moi, then use firmer rubber (black Perbunan et al) for the engaged position, and softer (clear silicone rubber) for the resting position.
The firmer rubber stops the alignment from varying under inconsistent thumb pressure, and the softer stuff gives the quietest possible return, which is only subject to spring tension (more or less a constant).
Anyway, yes, alignment makes an embarrassingly obvious difference if you've let it go for a while
The firmer rubber stops the alignment from varying under inconsistent thumb pressure, and the softer stuff gives the quietest possible return, which is only subject to spring tension (more or less a constant).
Anyway, yes, alignment makes an embarrassingly obvious difference if you've let it go for a while
- TriJim
- Posts: 63
- Joined: Sun Mar 25, 2018 3:42 pm
- Location: SouthCentral Pennsylvania
Re: Rotor Bumpers
Thanks for the tips and suggestions.
I use a drop of Ultra-Pure Light Bearing Oil for the piston spindle (under the valve cap) and a drop at the piston pivots near the bumpers. I also place UP Valve oil down the interior of the tubing as suggested. I use Hetman 15 on the Ball joints which keeps them quiet. No problem with operation of the valve (except the noise of the stops falling against the hard bumpers)
I would also note that the Bach A47 MLR trigger has two springs which contributes to a firmer trigger and return than models with a single trigger spring.
I haven't noticed if the Ultra-Pure Light Bearing Oil softens the neoprene bumpers and am suspicious that oil residues are contributing to the hardening of the bumpers.
Wondering - What is the experience of other trombone players with neoprene bumpers hardening? How long does it take and how often should they be replaced? ([On my trombone, the recommended Bach bumpers are 'noisy' hard in less than 6 months and disintegrate in less than one year). Is there another material that lasts longer and provides a quiet 'bump?' TIA
I use a drop of Ultra-Pure Light Bearing Oil for the piston spindle (under the valve cap) and a drop at the piston pivots near the bumpers. I also place UP Valve oil down the interior of the tubing as suggested. I use Hetman 15 on the Ball joints which keeps them quiet. No problem with operation of the valve (except the noise of the stops falling against the hard bumpers)
I would also note that the Bach A47 MLR trigger has two springs which contributes to a firmer trigger and return than models with a single trigger spring.
I haven't noticed if the Ultra-Pure Light Bearing Oil softens the neoprene bumpers and am suspicious that oil residues are contributing to the hardening of the bumpers.
Wondering - What is the experience of other trombone players with neoprene bumpers hardening? How long does it take and how often should they be replaced? ([On my trombone, the recommended Bach bumpers are 'noisy' hard in less than 6 months and disintegrate in less than one year). Is there another material that lasts longer and provides a quiet 'bump?' TIA
-
- Posts: 505
- Joined: Sun Jul 28, 2019 9:35 pm
- Location: New England
Re: Rotor Bumpers
Osmun outside boston has some kind of bumper material that they claim lasts longer and doesn’t dry out/harden. I like it so far.
Kris Danielsen D.M.A.
Westfield State University and Keene State College
Lecturer of Low Brass
Principal Trombone, New England Repertory Orchestra
2nd Trombone, Glens Falls Symphony
Westfield State University and Keene State College
Lecturer of Low Brass
Principal Trombone, New England Repertory Orchestra
2nd Trombone, Glens Falls Symphony
- BGuttman
- Posts: 6295
- Joined: Thu Mar 22, 2018 7:19 am
- Location: Cow Hampshire
Re: Rotor Bumpers
They may be using polyurethane. 70 durometer is plenty hard and never seems to change, even if exposed to solvents. We used to use the stuff for screen printing squeegees.Kdanielsen wrote: ↑Wed Nov 24, 2021 8:26 pm Osmun outside boston has some kind of bumper material that they claim lasts longer and doesn’t dry out/harden. I like it so far.
Bruce Guttman
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
-
- Posts: 1015
- Joined: Wed May 02, 2018 9:20 pm
Re: Rotor Bumpers
Instead of pulling the tuning slides, turn the horn so the bell points up, and drop the oil down the handslide receiver. Hold the valve "activated" so the oil lands on it, then, wiggle the valve.to distribute.
The problem with dropping down the tuning slides is the possibility of dragging grease and gunk into the valves from the insides of the tubes.
Matthew Walker
Owner/Craftsman, M&W Custom Trombones, LLC, Jackson, Wisconsin.
Former Bass Trombonist, Opera Australia, 1991-2006
Owner/Craftsman, M&W Custom Trombones, LLC, Jackson, Wisconsin.
Former Bass Trombonist, Opera Australia, 1991-2006
-
- Posts: 487
- Joined: Sat Sep 22, 2018 12:48 pm
- Location: Central Jersey
Re: Rotor Bumpers
You can also use a plastic straw to get the oil directly on.the valve, and bypass the tuning dlide grease.hornbuilder wrote: ↑Wed Nov 24, 2021 9:35 pmInstead of pulling the tuning slides, turn the horn so the bell points up, and drop the oil down the handslide receiver. Hold the valve "activated" so the oil lands on it, then, wiggle the valve.to distribute.
The problem with dropping down the tuning slides is the possibility of dragging grease and gunk into the valves from the insides of the tubes.
-
- Posts: 1053
- Joined: Fri Mar 23, 2018 11:33 pm
Re: Rotor Bumpers
Slices of vacuum cleaner belt last seemingly forever.
- harrisonreed
- Posts: 5165
- Joined: Fri Aug 17, 2018 12:18 pm
- Location: Fort Riley, Kansas
- Contact:
Re: Rotor Bumpers
The Osmun buna bumpers are what I've heard about. Never got to try them!